Sail Number, 12in, Black
Digital eight shaped sail number which requires cutting. This sail number will fit the Laser Radial, Laser Standard, Dart 16, Laser Vago, Sunfish, Funboat and Laser Bahia.
Laser 4.7, Radial and Standard Instructions for Applying Sail Numbers
Class Rule 4 (with 27(e) for Laser Radial and 28(e) for Laser 4.7) require that your sail numbers (and National Letters if used) are
a certain size and colour and are placed on the sail in a certain position. National Letters are only required at World and
Continental Championships and other events described as international events in their notices of race and sailing instructions.
Numbers/letters drawn on the sail with permanent ink pens or similar are illegal.
Style and Colour
Each number/letter must be upright, solid (not outline), a uniform thickness and easy to read. Each number/letter must be one
colour only. All the letters must be the same colour. The last 4 digits of the number must be the same dark colour (preferably
black). Any preceding digits must be all red or a single different contrasting colour. The colours must be dense and contrast so that
they are easy to read.
Laser 4.7, Radial and Standard Applying Sail Numbers
1. If your sail has been used it should be sponged clean with mild soap and warm water and allowed to dry completely.
2. Find a clean, large flat working surface (a table or clean hard floor).
STARBOARD SIDE NUMBERS
3. Spread the sail out flat on the working surface so that the starboard side of the sail is facing up. (To find the starboard side the
luff sleeve should be on the RIGHT hand side of the sail when laid flat.)
4. Refer to the instructions below and sail diagrams of the Laser, Laser Radial and Laser 4.7 sail for measuring and drawing
pencil Base Lines on the sail and for cutting a template out of cardboard or stiff paper both as a guide for the position of
characters, spaces between each character and between rows.
5. Following the instructions below draw a pencil Base Line for the starboard numbers. This Base Line will locate the bottom
edge of the starboard numbers.
6. Make a small pencil mark 100 mm from the leech on the Base Line.
7. Place the smaller edge of the template on the line immediately to the left of the pencil mark so that the template is at 90
degrees to the line. This is the starting point for the first number.
8. Peel and fold back 10 mm of backing from the base of the first number. Place the number on the sail against the right hand
edge of the template with the base of the number just touching the pencil line.
Check that the number is lined up with the Base Line and template and press the base of the number on to the sail. Lift the
remainder of the number and slowly peel off the backing as you smooth the number on to the sail taking care to remove air
bubbles and creases.
9. For the second and subsequent numbers on the starboard side place the template alongside the right hand edge of the
previous number to space the next number correctly.
PORT SIDE NUMBERS
10. Turn the sail over and flatten the sail (the luff sleeve should now be on the LEFT hand side of the sail).
11. Following the instructions below draw a pencil Base Line for the port numbers.
12. Make a small pencil mark 100 mm from the leech on the Base Line.
13. Lay all the numbers on the sail using the spacing template and check that the full number is correct.
14. Apply the number closest to the leech (the last digit in the sail number) first using the base line and the template working
away from the leech.
STARBOARD SIDE LETTERS
15. Turn the sail over and flatten the sail (the luff sleeve should now be on the RIGHT hand side of the sail).
16. Following the instructions below draw a pencil Base Line for the starboard letters.
17. Follow instructions 6 to 9 above.
PORT SIDE LETTERS
18. Turn the sail over and flatten the sail (the luff sleeve should now be on the LEFT hand side of the sail).
19. Follow instructions 11 to 14 above.sku: 95853
Adding product to your cart
- choosing a selection results in a full page refresh
- press the space key then arrow keys to make a selection